Factory-Reconditioned BOSTITCH U/SB-1664FN 1-Inch to 2-1/2-Inch 16-Gauge Finish Nailer

Factory-Reconditioned BOSTITCH U/SB-1664FN 1-Inch to 2-1/2-Inch 16-Gauge Finish Nailer

Factory-reconditioned straight finish nailer kit for use on interior and exterior finish and trim, furniture, cabinet work, and staircases
Adjustable exhaust that conveniently directs exhaust away from the user's face
No-mar tip; lightweight aluminum design; adjustable depth guide; soft rubber grip
Includes 1/4-inch air fitting, 1,000 2-inch nails, a carrying case, and oil
Weighs just 4-pounds

The Bostitch straight finish nailer kit has a lightweight aluminum design and a tool-free adjustable exhaust that conveniently directs exhaust away from your face. Its no-mar tip protects sensitive worksurfaces, and its adjustable depth guide sets nails to just the right depth quickly and conveniently. The SB-1664FN is great for interior and exterior finish and trim, furniture, cabinet work, and staircases. This kit includes the nailer, a 1/4-inch air fitting, 1,000 two-inch nails, a carrying case, and oil.

List Price:$139.00
Price:

Pneumatic Flooring Nailer By Hardcore Tools® - Great for Bamboo, Oak, Maple, Brazilian Cherry, Hickory, Walnut, Hand Scraped, Prefinished and Engineered Wood Flooring

Pneumatic Flooring Nailer By Hardcore Tools® - Great for Bamboo, Oak, Maple, Brazilian Cherry, Hickory, Walnut, Hand Scraped, Prefinished and Engineered Wood Flooring

Pneumatic flooring nailer Hardcore Tools® Brand) light weight cast aluminum, colors may vary!
Operates with any standard compressor between 60-100 PSI
High-capacity magazine for reload time. Reliably drives staples at proper angle and depth.
Non-marring base plates are adjustable for 1/2 to 3/4 inch hardwood floor installation.
Durable plastic carrying case for tool, inclues mallet, oil, hex tools, o-rings and safety googles.

Pneumatic Flooring Nailer for installing hardwood floors between 1/2 - 3/4 inches thick. Used by many contractors and DIY floor installers this tool works well for all skill levels. The sturdy long handle allows for great control and keeps you from breaking your back. The nail magazine holds 100 floor nails, and nail length can vary between 1 1/2" to 2" depending on what you need. The air inlet is standard 1/4". Air consumption is low at 4.5 CFM and allows you to use a small compressor. Input pressure should be controlled between 60 and 100 PSI. With a little practice this tool will allow you to lay hundreds of square feet per day. Depending on the type of wood you will need to vary the input pressure. Bamboo is very hard and brittle and requires a low pressure to prevent damage. Teak and some other very dense hard woods will require 100 PSI. You should test on a piece of scrap plank to make sure you are getting good results. The pneumatic flooring nailer is used by placing it on the edge of a piece of hardwood flooring. The included mallet is then used to strike the actuator and fire the nail in. The most difficult part of the process is just moving the pneumatic flooring nailer around. Include in the kit is a Carrying Case, Pneumatic Flooring Nailer , Safety Glasses, Air Tool Oil, Base Plate, S3 Hex Key S4 Hex Key S5 Hex Key Wrench, and Instruction Manual.

List Price:$249.99
Price: $189.99

DEWALT D51256K 1-1/4-Inch to 2-1/2-Inch 16-Gauge Finish Nailer

DEWALT D51256K 1-1/4-Inch to 2-1/2-Inch 16-Gauge Finish Nailer

Two things set this tool apart from its classmates: the large nail capacity and the rear-loading magazine that lets you lock and load, or load and lock. The tool is light, comfortable, and sturdy, features DeWalt's ingenious tool-free jam-clearing mechanism, and offers a fantastic line of sight. The sliding depth adjustment is further evidence of DeWalt's creative problem-solving abilities. Unlock it with your index finger, slide the adjustment with your other hand, and you're ready to fire. This model has a nice plus in the 360-degree swivel exhaust cap. Great pad, too--it didn't mar anything to which we introduced it. Finally, and this may not seem like a big deal, but in everyday use you're going to love the reversible belt/rafter hook. --Kris Jensen-Van Heste

List Price:$359.22
Price:

Milwaukee 7140-21 15 Gauge 1-Inch to 2-1/2-Inch Angled Finish Nailer

Milwaukee 7140-21 15 Gauge 1-Inch to 2-1/2-Inch Angled Finish Nailer

1-inch to 2-1/2-inch gauge angled finish nailer; tool-free depth adjustment; reload indicator
70-120 psi operating pressure; 106 nail capacity; sequential and bump firing modes
Lightweight magnesium housing, soft rubber grip
Includes nailer, safety glasses, oil, 5 hex wrenches, case, 15-gauge nails (1,000)
4.2 pounds; 5-year warranty

Includes: Safety Glasses, 2 oz. Oil, 4 mm Hex Wrench, 5 mm Hex Wrench, 1 Box (1000) Nails, Carrying Case.

Milwaukee's Heavy-Duty 34-Degree 15 gauge Angle Finish Nailer has an ultra lightweight magnesium housing to minimize fatigue. Its ergonomic grip and balance combined with its compact size offers great control and maneuverability. Its reload indicator is a rare feature in an angle finish nailer and is important in preventing missing nails in trim work. The textured selectable trigger lets you choose sequential or contact actuation by simply turning a knob. The rear-loading magazine with a bypass pusher allows quick loading and unloading of fasteners. The easy load magazine holds 106 nails in 1 in. to 2-1/2 in. lengths. The self-cleaning air filter extends life by preventing dirt and debris from entering the tool. The adjustable air deflector with muffler directs exhaust away from the work area and holds down the noise. An adjustable and removable belt hook provides convenience for carrying. The tool-free depth of drive adjustment provides precise depth control. A tool-free jam release allows for quick access for clearing occasional jams. Operating Pressure: 70-120 PSI. Collation Angle: 34 degrees. Air Consumption at 100 PSI: .07 cu. ft. / cycle. Air Inlet: 3/8" NPT. Magazine Capacity: 106 nails. Tool Weight: 4.2 lbs.

List Price:$370.00
Price:

Flooring Nailer for Hardwood Floors Hardcore Tools® - Great for Bamboo, Oak, Maple, Brazilian Cherry, Hickory, Walnut, Hand Scraped, Prefinished and Engineered Wood Flooring

Flooring Nailer for Hardwood Floors Hardcore Tools® - Great for Bamboo, Oak, Maple, Brazilian Cherry, Hickory, Walnut, Hand Scraped, Prefinished and Engineered Wood Flooring

Hardwood flooring nailer (Hardcore Tools® Brand) light weight cast aluminum, colors may vary!
Operates with any standard compressor between 60-100 PSI
High-capacity magazine for reload time. Reliably drives staples at proper angle and depth.
Non-marring base plates are adjustable for 1/2 to 3/4 inch hardwood floor installation.
Durable plastic carrying case for tool, inclues mallet, oil, hex tools, o-rings and safety googles.

Flooring Nailer for installing hardwood floors between 1/2 - 3/4 inches thick. Used by many contractors and DIY floor installers this tool works well for all skill levels. The sturdy long handle allows for great control and keeps you from breaking your back. The nail magazine holds 100 flooring nails, and nail length can vary between 1 1/2" to 2" depending on what you need. The air inlet is standard 1/4". Air consumption is low at 4.5 CFM and allows you to use a small compressor. Input pressure should be controlled between 60 and 100 PSI. With a little practice this tool will allow you to lay hundreds of square feet per day. Depending on the type of wood you will need to vary the input pressure. Bamboo is very hard and brittle and requires a low pressure to prevent damage. Teak and some other very dense hard woods will require 100 PSI. You should test on a piece of scrap plank to make sure you are getting good results. The flooring nailer is used by placing it on the edge of a piece of hardwood flooring. The included mallet is then used to strike the actuator and fire the cleat nail in. The most difficult part of the process is just moving the flooring nailer around. Include in the kit is a Carrying Case, Flooring Nailer , Safety Glasses, Air Tool Oil, Base Plate, S3 Hex Key S4 Hex Key S5 Hex Key Wrench, and Instruction Manual.

List Price:$249.99
Price: $189.99

Buffalo Tools ANFIN 2-Inch 18 Gauge Finish Nailer

Buffalo Tools ANFIN 2-Inch 18 Gauge Finish Nailer

Great for general purpose carpentry work, 100 brad capacity
Rubberized handle for a comfortable grip , Lightweight, 3-Pound design
55-95 psi operating pressure, 1/4-Inch NPT inlet
Includes oiler bottle and 2-hex key wrenches
Storage case included

Make your projects look professionally finished with the Buffalo Tools Pneumatic Nail and Staple Gun. Don't dent and chip the surface of the of your expensive, high quality lumber by driving nails in by hand. Use our Pneumatic Nail and Staple Gun to cleanly drive nail heads below the surface of the wood, saving you time and improving the quality of your work. The Buffalo Tools 2-Inch 18 Gauge Finish Nailer can fit into tight spaces like corners and closets when you are installing baseboards, crown molding and door casings. This Finish Nailer can drive up to 100 brad nails per coil.

List Price:$54.99
Price: $44.86

Floor Stapler for Installing Hardwood Flooring - Bamboo, Oak, Maple, Brazilian Cherry, Hickory, Walnut, Hand Scraped, Prefinished and Engineered Wood Flooring

Floor Stapler for Installing Hardwood Flooring - Bamboo, Oak, Maple, Brazilian Cherry, Hickory, Walnut, Hand Scraped, Prefinished and Engineered Wood Flooring

Floor stapler (Hardcore Tools® Brand) light weight cast aluminum, colors may vary!
Operates with any standard compressor between 60-100 PSI
High-capacity magazine for reload time. Reliably drives staples at proper angle and depth.
Non-marring base plates are adjustable for 1/2 to 3/4 inch hardwood floor installation.
Durable plastic carrying case for tool, inclues mallet, oil, hex tools, o-rings and safety googles.

Floor Stapler for installing hardwood floors between 1/2 - 3/4 inches thick. Used by many contractors and DIY floor installers this tool works well for all skill levels. The sturdy long handle allows for great control and keeps you from breaking your back. The staple magazine holds 100 floor staples, and staple length can vary between 1 1/2" to 2" depending on what you need. The air inlet is standard 1/4". Air consumption is low at 4.5 CFM and allows you to use a small compressor. Input pressure should be controlled between 60 and 100 PSI. With a little practice this tool will allow you to lay hundreds of square feet per day. Depending on the type of wood you will need to vary the input pressure. Bamboo is very hard and brittle and requires a low pressure to prevent damage. Teak and some other very dense hard woods will require 100 PSI. You should test on a piece of scrap plank to make sure you are getting good results. The floor stapler is used by placing it on the edge of a piece of hardwood floor. The included mallet is then used to strike the actuator and fire the staple in. The most difficult part of the process is just moving the floor stapler around. Include in the kit is a Carrying Case, Floor Stapler , Safety Glasses, Air Tool Oil, Base Plate, S3 Hex Key S4 Hex Key S5 Hex Key Wrench, and Instruction Manual.

List Price:$249.99
Price: $189.99

Floor Nailer for Installing Hardwood Flooring - Bamboo, Oak, Maple, Brazilian Cherry, Hickory, Walnut, Hand Scraped, Prefinished and Engineered Wood Flooring

Floor Nailer for Installing Hardwood Flooring - Bamboo, Oak, Maple, Brazilian Cherry, Hickory, Walnut, Hand Scraped, Prefinished and Engineered Wood Flooring

Floor nailer (Hardcore Tools® Brand) light weight cast aluminum, colors may vary!
Operates with any compressor with standard connectors, 60-100 PSI
High-capacity magazine for reload time. Reliably drives staples at proper angle and depth.
Non-marring base plates are adjustable for 1/2 to 3/4 inch hardwood floor installation.
Durable plastic carrying case for tool, inclues mallet, oil, hex tools, o-rings and safety googles.

Floor Nailer for installing hardwood floors between 1/2 - 3/4 inches thick. Used by many contractors and DIY floor installers this tool works well for all skill levels. The sturdy long handle allows for great control and keeps you from breaking your back. The nail magazine holds 100 floor nails, and nail length can vary between 1 1/2" to 2" depending on what you need. The air inlet is standard 1/4". Air consumption is low at 4.5 CFM and allows you to use a small compressor. Input pressure should be controlled between 60 and 100 PSI. With a little practice this tool will allow you to lay hundreds of square feet per day. Depending on the type of wood you will need to vary the input pressure. Bamboo is very hard and brittle and requires a low pressure to prevent damage. Teak and some other very dense hard woods will require 100 PSI. You should test on a piece of scrap plank to make sure you are getting good results. The floor nailer is used by placing it on the edge of a piece of hardwood flooring. The included mallet is then used to strike the actuator and fire the nail in. The most difficult part of the process is just moving the floor nailer around. Include in the kit is a Carrying Case, Floor Nailer , Safety Glasses, Air Tool Oil, Base Plate, S3 Hex Key S4 Hex Key S5 Hex Key Wrench, and Instruction Manual. Good luck on installing your new hard wood floor.

List Price:$249.99
Price: $189.99

Factory-Reconditioned BOSTITCH U/MCN250 2-1/2-Inch Strapshot Metal Connector Nailer

Factory-Reconditioned BOSTITCH U/MCN250 2-1/2-Inch Strapshot Metal Connector Nailer

Exposed nail tip places fastener point directly into connector holes for a faster, more precise application
In-line magazine offers improved balance for added maneuverability
Adjustable rafter hook allows user to hang tool on rafters and joists
Exclusive nail management feature helps to prevent jamming (patent pending)
Drives 1-1/2-Inch and 2-1/2-Inch STRAPSHOT fasteners as well as other paper tape collated metal connector nails

This is a factory reconditioned product. Reconditioned generally means that the product has been returned to the manufacturer, who brings the product back to like new condition. Some products may contain cosmetic blemishes. Includes 2-1/2-in Strapshot Metal Connector Nailer - MCN250-R, Carrying Case

List Price:$379.00
Price:

DEWALT DC612KA 1-1/4-Inch to 2-1/2-Inch 12-Volt / 14.4-Volt Ni-Cad Cordless 16-Gauge Straight Finish Nailer

DEWALT DC612KA 1-1/4-Inch to 2-1/2-Inch 12-Volt / 14.4-Volt Ni-Cad Cordless 16-Gauge Straight Finish Nailer

No compressor. No hoses. No kidding. And no sacrifices in speed or power, either. There's absolutely no comparison between this performer and the fuel-cell powered competition, which we thought was a great innovation. But there's no costly fuel cell to replace on this tool—-just pop on a recharged XRP battery and get back on the job. The only difference you'll feel between this and a traditional pneumatic is that you're not tethered to an air hose. It's just as fast and fires just as powerfully into both soft and hard joints. We love that you can choose bump or sequential mode for precision or speed, something most nailers don't offer, and the integrated headlight is another impressive addition, really lighting up your workpiece even in the worst conditions. There's a fantastic six-position numbered dial to reference your depths, so you can move easily between, for example, baseboard and crown molding without struggling to reset the depth. DeWalt's covered what would have been our main safety concern: An air tool can't fire without a hose, but what's to keep this one from being accidentally fired? They've built in a contact trip lock-off. We were pleased with the troubleshooting process, too—the nosepiece is clear and very accessible, letting you clear a jammed fastener without screwdrivers or wrenches, though we couldn't get it to jam for us. Rear loading is simple and fast, and it accepts most brands of 16-gauge nails. It's built tough for the job site, but the home hobbyist would love this tool. Just hook it on your tool belt and go; it's one of the coolest tools we've seen, and the kit has everything you need: a one-hour charger, two 14.4V XRP batteries, reversible belt hook, no-mar tip, safety glasses and the heavy-duty kit box.--Kris Jensen-Van Heste

List Price:$700.00
Price: $260.00

WHAM 61867WM Angle Finish Nailer 2-1/2 inch

WHAM 61867WM Angle Finish Nailer 2-1/2 inch

Ideal for construction projects
Drives 1 1/2" to 2 1/2" clipped head nails (15 gauge)
70-120 PSI operating pressure
Adjustable depth and exhaust deflector
Includes lubricating oil, adjusting wrenches, safety glasses and custom carrying case

List Price:$129.99
Price: $83.36

BOSTITCH SFN250K 1-inch to 2-1/2-Inch 16-Gauge Finish Nailer

BOSTITCH SFN250K 1-inch to 2-1/2-Inch 16-Gauge Finish Nailer

Drives 1 to 2 1/2-inch 16-gauge finish nails
Tool-free adjustable depth setting
Tool free adjustable exhaust
No-Mar tip with on-tool storage
Quick released nose for clearing jams; 1-year limited warranty

There’s no quicker, easier way to install interior trim than with a pneumatic nailer. But, there are dozens of pneumatic nailers on the market and it’s important to choose the correct one. The Stanley SFN250K is specifically designed for installing all sizes and types of wood molding including baseboard, chair rail, door and window casing, shoe molding, and crown molding. It’s also suitable for cabinetmaking and woodworking.The 3.4-pound tool drives 16-gauge nails, which are very thin with tiny T-shaped heads. As a result, the nails are less likely to split delicate moldings and they leave behind barely visible holes. The SFN250K accepts nails ranging in length from 1 inch to 2-1/2 inch; its straight magazine holds up to 100 nails.Additional features include an adjustable depth setting, rotating exhaust deflector, no-mar rubber tip, and a quick-release mechanism that makes it easy to clear out jammed nails. The tool comes complete with a blow-molded plastic carrying case and 500 nails. -- Joseph TruiniWhat’s in the Box:Stanley SFN250K 16-gauge finish nailer, 500 2-1/2-inch nails, lubricating oil, carrying case, instructional manual

List Price:$149.00
Price:

DEWALT DC616KA 1-1/2-Inch to 2-1/2-Inch 18-Volt Ni-Cad Cordless 16-Gauge Straight Finish Nailer Kit

DEWALT DC616KA 1-1/2-Inch to 2-1/2-Inch 18-Volt Ni-Cad Cordless 16-Gauge Straight Finish Nailer Kit

No compressor. No hoses. No kidding. And no sacrifices in speed or power, either. There's absolutely no comparison between this performer and the fuel-cell powered competition, which we thought was a great innovation. But there's no costly fuel cell to replace on this tool—-just pop on a recharged XRP battery and get back on the job. The only difference you'll feel between this and a traditional pneumatic is that you're not tethered to an air hose. It's just as fast and fires just as powerfully into both soft and hard joints. We love that you can choose bump or sequential mode for precision or speed, something most nailers don't offer, and the integrated headlight is another impressive addition, really lighting up your workpiece even in the worst conditions. There's a fantastic six-position numbered dial to reference your depths, so you can move easily between, for example, baseboard and crown molding without struggling to reset the depth. DeWalt's covered what would have been our main safety concern: An air tool can't fire without a hose, but what's to keep this one from being accidentally fired? They've built in a contact trip lock-off. We were pleased with the troubleshooting process, too—the nosepiece is clear and very accessible, letting you clear a jammed fastener without screwdrivers or wrenches, though we couldn't get it to jam for us. Rear loading is simple and fast, and it accepts most brands of 16-gauge nails. It's built tough for the job site, but the home hobbyist would love this tool. Just hook it on your tool belt and go; it's truly one of the coolest tools we've seen and the kit has everything you need: a one-hour charger, two 18V XRP batteries, reversible belt hook, no-mar tip, safety glasses and the heavy-duty kit box.--Kris Jensen-Van Heste

List Price:$740.00
Price: $356.62

Factory-Reconditioned DEWALT D51256KR 1-1/4-Inch to 2-1/2-Inch 16-Gauge Finish Nailer

Factory-Reconditioned DEWALT D51256KR 1-1/4-Inch to 2-1/2-Inch 16-Gauge Finish Nailer

List Price:$288.00
Price:

BOSTITCH SDA250K 15 Gauge 1-Inch to 2-1/2-Inch Angled Finish Nailer

BOSTITCH SDA250K 15 Gauge 1-Inch to 2-1/2-Inch Angled Finish Nailer

Drive 1 to 2-1/2-inch DA-Style 15-gauge finish nails; angled magazine permits use in tight spaces
Tool free adjustable depth-of-drive setting; tool free adjustable exhaust control
No-mar tip;wWeighs just 4.2 pounds
Quick-release nose for clearing jams
1-year limited warranty

Drive nails with lightning speed and incredible ease with the Stanley SDA250K angled finish nailer. This versatile air-powered tool accepts 15-gauge, D-head finishing nails ranging in length from 1 to 2-1/2 inches long. The tool’s angled magazine allows nailing in tight spaces and corners, making it ideal for installing crown molding, shoe molding and tongue-and-groove flooring and paneling. The magazine holds up to 100 nails, which easily load from the rear. Also, the 15-gauge, D-head nails provide more hold down power than the thinner 16-gauge nails used in most other finish nailers. Therefore, this tool can be used to fasten larger, thicker pieces.The SDA250K has a working air-pressure range of 70 to 120 pounds per square inch. It features a non-marring rubber tip, adjustable depth setting and a quick-release nose for clearing jammed nails. This tool can handle a wide range of woodworking and carpentry applications, including interior and exterior trim work, cabinetry assembly, furniture making and stair building. And at just over 4 pounds, you can use it all day without becoming fatigued.-- Joseph TruiniWhat’s in the BoxStanley SDA250K 15-gauge finish nailer, five hundred 2-1/2-inch nails, lubricating oil, plastic carrying case.

List Price:$189.00
Price:

Ridgid R250SFA 2-1/2-Inch Finish Nailer

Ridgid R250SFA 2-1/2-Inch Finish Nailer

Powerful motor ? drives a 2-1/2 inch finish nail into solid oak
Rear loading magazine with by-pass pusher ? for quick 2-step reloading
Tool-free jam release ? for easy clearing to keep you going
2 No-mar pads ? to keep work surface clean of tool marks
16 gauge fastener diameter

Includes 16 Gauge 2-1/2-in Straight Finish Nailer - ZRR250SFA, 1,000 Nails, Eye Protection, (3) Wrenches, (2) No-Mar Pads, Oil, Case

List Price:$241.00
Price: $239.99

Senco GT65RHA 16 Ga. 2 1/2" Cordless Gas 20° Angled Brad Nailer

Senco GT65RHA 16 Ga. 2 1/2" Cordless Gas 20° Angled Brad Nailer

5S0001N 16GANGLE FINISH NAILER
16GANGLE FINISH NAILER




No hoses, no compressors, high voltage ignition gives you more power and cleaner combustion. Consistent drives in all weather conditions. Metal magazine for increased durability, belt hook, thumbwheel depth of drive and EZ-Clear. Specs: sequential actuation trigger, Ni-MH 6v battery, charger: 2 hours, fuel cell: Senco 18g or compatible, fastener capacity: 110, compatible fasteners: type: RH, gauge: 16, range: 1 1/4"-2-1/2", collation: 20 degree. HxLxW 305mmx318mmx91mm, weighs 2.22kg. Includes (1) each: case, Ni-MH battery and charger.

List Price:$359.99
Price: $155.00